repetier server and wanhao duplicator 4s

#Repetier server and wanhao duplicator 4s update#
#Repetier server and wanhao duplicator 4s full#

Not every time but has done it twice out of about 10 test prints using RH. It will make the printer go crazy sometimes and run the print head lower than the bed and then try to move the bed and or run the print head into the bed in the middle and not stop and gears grinding and noises galore. I would really love to get Repetier Host running since I can monitor it remotely and I don't have to move the SD card constantly. But anything else I try print that I download, most of the time fails. I've opened one of the included files on the SD card into Cura and saved the profile. If I print something from Thingiverse, it will print correctly only OCCASIONALLY. If I print something from the included SD card, it will print correctly MOST OF THE TIME. Instead of making that post any bigger I wanted to seperate the question about config files. Simple and fast is our mission.I'm having nothing but problems printing that I detailed in another post. 2Gb card is sufficient for any 3D file and keep as many file as you like. Awesome, all your printer job can be done by this small card. For this reason, we developed SD card reader on printer. Sometimes customer failed in printing with computer USB link, due to the computer sleep or shut down automatically. Oh yeah, and the electronics are all inside, so you don't have wires dangling everywhere.

All you have to do is sit back and relax while your Duplicator 4s does all the work. When you hit print, the machine will automatically home itself, heat up, and begin printing.

#Repetier server and wanhao duplicator 4s full#

We've also added full end stop support so that you never need to touch the XYZ axes ever again. The Duplicator 4s connects to your computer via a standard USB cable thanks to a USB chip on the motherboard. The new electronics have been designed to make the printing experience easier than ever.

This means the layer changes are almost completely imperceptible.Ĭonnect over USB and hit print - the machine will calibrate itself and start printing. Using a high-angle lead screw, we were able to increase the speed of the Z axis from 150mm/minute to 1,000mm/minute. Guided by two of the linear shafts, this completely eliminates any Z wobble and results in nicely aligned layers. i have to say, it's great the web interface of the server is useful, too - but the host program really makes it. i've used both octoprint and the repetier server/host setup. We've completely replaced the Z axis with a stepper driver, centilevered stage. I am looking at may be using Repetier Server to control the 8 printers we have at the office, but I wanted to see if anyone here has used it/liked it/disliked it first. These are very forgiving to DIY assembly and provide a nice, smooth motion on the steel shafts. We've also switched to self-aligning, sintered stainless steel bearings. This is probably overkill, but you can trust that the axes will be sturdy. The entire system has been upgraded to sturdy 3/8″ diameter linear shafting. We've completely overhauled the drive system to give the optimum positioning accuracy. The layer alignment is much better which results in nicer prints and higher resolution, 100 micron inch. And since it's designed from the ground up for 1.75 mm filament, it's light-years ahead of past designs in small-filament reliability. We've learned a lot over our past extruder designs, and incorporated a lot of those lessons here: that's why it's smaller, lighter, and faster to build. This extruder was designed from scratch, and contains a number of custom manufactured parts. The Duplicator 4s has our latest dedicated 1.75 mm filament extruder. Filament Capabilities: ABS, PLA, PVA, NYLON, HIPS and other common filaments.If you want to unlock the full potential of the printer we recommend that you buy SIMPLIFY 3D with the printer, but if you choose not to, ReplicatorG is included. Other features include upgraded electronics and 1/16 micro-stepping motor control. Use two different colors or use one of the extruders with HIPS or PVA as support material.

The Duplicator 4s is equipped with the new MK10 Dual-Extruder set for dual printing. The 4s features a heated build plate and fully enclosed build area to ensure accurate prints and a stable temperature which helps prevent shrinking and warping of plastics.

It comes in a black steel exoframe, which makes it very stable and vibration safe.

#Repetier server and wanhao duplicator 4s update#

This is the latest update in the Duplicator 4 series and is really a wonderful printer, it comes with all of the benefits of Duplicator 4x. Say Hello to the newest addition in the Duplicator 4 family, the brand new Wanhao Duplicator 4s!